# UL 62841-2-14 UL 62841-2-14-2016 - 标准号：UL 62841-2-14　年份：2016　文件名状态：— - 来源 PDF：`安全标准\电动工具\particular standard(专用标准）\hand-held tool (手持式工具）\planer(电刨）\北美\UL 62841-2-14-2016.pdf` - 页数：35　提取字符：53,086　页眉页脚过滤：3 条 - 文字层完整性：full（每页数字中位数 56.5）　语种：英文　小数：完整 108 / 疑似残缺 0 - 提取时间：2026-11-03　方式：文字层直提（未 OCR） - 正文可疑：否 > 本页眉之后是原文，按页排列。**表格线、图样、尺寸标注在纯文本里会走形，判定试验参数时以 PDF 原件为准。** This document is only permissible for use by claire.hu@intertek.com of Intertek, Electrical/Wireless, Qinzhou, Shanghai, China. 1/5/2017 5:06:55 AM 62841-2-14 STANDARD FOR SAFETY Electric Motor-Operated Hand-Held Tools, Transportable Tools And Lawn And Garden Machinery – Safety – Part 2-14: Particular Requirements For Hand-Held Planers UL COPYRIGHTED MATERIAL – NOT AUTHORIZED FOR FURTHER REPRODUCTION OR This document is only permissible for use by claire.hu@intertek.com of Intertek, Electrical/Wireless, Qinzhou, Shanghai, China. 1/5/2017 5:06:55 AM UL COPYRIGHTED MATERIAL – NOT AUTHORIZED FOR FURTHER REPRODUCTION OR AUGUST 12, 2016 −UL 62841-2-14 tr1 UL Standard for Safety for Electric Motor-Operated Hand-Held Tools, Transportable Tools And Lawn And Garden Machinery – Part 2-14: Particular Requirements For Hand-Held Planers, UL 62841-2-14 This document is only permissible for use by claire.hu@intertek.com of Intertek, Electrical/Wireless, Qinzhou, Shanghai, China. 1/5/2017 5:06:55 AM First Edition, Dated August 12, 2016 Summary of Topics Adoption Of The First Edition Of IEC 62841-2-14, Standard For Electric Motor-Operated Hand-Held Tools, Transportable Tools And Lawn And Garden Machinery – Safety – Part 2-14: Particular Requirements for Hand-Held Planers, As The First Edition Of UL 62841-2-14 This standard is an adoption of IEC 62841-2-14, Edition 1, published by the IEC June 2015. There are no technical national differences for this standard. The new requirements are substantially in accordance with Proposal(s) on this subject dated March 18, All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form by any means, electronic, mechanical photocopying, recording, or otherwise without prior permission of UL. UL provides this Standard ″as is″ without warranty of any kind, either expressed or implied, including but not limited to, the implied warranties of merchantability or fitness for any purpose. In no event will UL be liable for any special, incidental, consequential, indirect or similar damages, including loss of profits, lost savings, loss of data, or any other damages arising out of the use of or the inability to use this Standard, even if UL or an authorized UL representative has been advised of the possibility of such damage. In no event shall UL’s liability for any damage ever exceed the price paid for this Standard, regardless of the form of the claim. Users of the electronic versions of UL’s Standards for Safety agree to defend, indemnify, and hold UL harmless from and against any loss, expense, liability, damage, claim, or judgment (including reasonable attorney’s fees) resulting from any error or deviation introduced while purchaser is storing an electronic Standard on the purchaser’s computer system. UL COPYRIGHTED MATERIAL – NOT AUTHORIZED FOR FURTHER REPRODUCTION OR AUGUST 12, 2016 −UL 62841-2-14 tr2 This document is only permissible for use by claire.hu@intertek.com of Intertek, Electrical/Wireless, Qinzhou, Shanghai, China. 1/5/2017 5:06:55 AM No Text on This Page UL COPYRIGHTED MATERIAL – NOT AUTHORIZED FOR FURTHER REPRODUCTION OR CSA Group CAN/CSA-C22.2 No. 62841-2-14:16 First Edition (IEC 62841-2-14:2015) Underwriters Laboratories Inc. UL 62841-2-14 First Edition Electric Motor-Operated Hand-Held Tools, Transportable Tools And Lawn And Garden Machinery – Safety – Part 2-14: Particular Requirements For Hand-Held Planers August 12, 2016 This national standard is based on publication IEC 62841-2-14 First Edition (2015). UL COPYRIGHTED MATERIAL – NOT AUTHORIZED FOR FURTHER REPRODUCTION OR ANSI/UL 62841-2-14-2016 This document is only permissible for use by claire.hu@intertek.com of Intertek, Electrical/Wireless, Qinzhou, Shanghai, China. 1/5/2017 5:06:55 AM Approved by Commitment for Amendments This document is only permissible for use by claire.hu@intertek.com of Intertek, Electrical/Wireless, Qinzhou, Shanghai, China. 1/5/2017 5:06:55 AM This standard is issued jointly by the Canadian Standards Association (operating as “CSA Group”) and Underwriters Laboratories Inc. (UL). Comments or proposals for revisions on any part of the standard may be submitted to CSA Group or UL at any time. Revisions to this standard will be made only after processing according to the standards development procedures of CSA Group and UL. CSA Group and UL will issue revisions to this standard by means of a new edition or revised or additional pages bearing their date of issue. ISBN 978-1-4883-0484-2 © 2016 CSA Group All rights reserved. No part of this publication may be reproduced in any form whatsoever without the prior permission of the publisher. This Standard is subject to review five years from the date of publication, and suggestions for its improvement will be referred to the appropriate committee. To submit a proposal for change, please send the following information to inquires@csagroup.org and include ″Proposal for change″ in the subject line: Standard designation (number); relevant clause, table, and/or figure number; wording of the proposed change; and rationale for the change. To purchase CSA Group Standards and related publications, visit CSA Group’s Online Store at shop.csa.ca or call toll-free 1-800-463-6727 or 416-747-4044. Copyright © 2016 Underwriters Laboratories Inc. Comments or proposals for revisions on any part of the Standard may be submitted to UL at any time. Proposals should be submitted via a Proposal Request in UL’s On-Line Collaborative Standards Development System (CSDS) at http://csds.ul.com. This ANSI/UL Standard for Safety consists of the First Edition. The most recent designation of ANSI/UL 62841-2-14 as an American National Standard (ANSI) occurred on August 12, 2016. The ANSI approval for this standard does not include the Cover Page, Transmittal Pages, Title Page, Preface Page, National Difference Page or IEC Foreword. Comments or proposals for revisions on any part of the Standard may be submitted to UL at any time. Proposals should be submitted via a Proposal Request in UL’s On-Line Collaborative Standards Development System (CSDS) at http://csds.ul.com. To purchase UL Standards, visit Comm 2000 at http://www.comm-2000.com/help/how_to_order.aspx or call toll-free 1-888-853-3503. UL COPYRIGHTED MATERIAL – NOT AUTHORIZED FOR FURTHER REPRODUCTION OR CONTENTS This document is only permissible for use by claire.hu@intertek.com of Intertek, Electrical/Wireless, Qinzhou, Shanghai, China. 1/5/2017 5:06:55 AM Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 NATIONAL DIFFERENCES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 FOREWORD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 1 Scope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 2 Normative references . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 3 Terms and definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 4 General requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 5 General conditions for the tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 6 Radiation, toxicity and similar hazards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 7 Classification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 8 Marking and instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 9 Protection against access to live parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13 10 Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13 11 Input and current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13 12 Heating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13 13 Resistance to heat and fire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13 14 Moisture resistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13 15 Resistance to rusting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13 16 Overload protection of transformers and associated circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13 17 Endurance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13 18 Abnormal operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13 19 Mechanical hazards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 19.111 Lift-off device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 20 Mechanical strength . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 21 Construction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 22 Internal wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 23 Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 24 Supply connection and external flexible cords . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 25 Terminals for external conductors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 26 Provision for earthing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 27 Screws and connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 28 Creepage distances, clearances and distances through insulation . . . . . . . . . . . . . . . . . . . . . . . .17 Annexes Annex I (informative) Measurement of noise and vibration emissions I.2 Noise test code (grade 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22 I.2.4 Installation and mounting conditions of the power tools during noise tests . . . . . . . . . . .22 I.2.5 Operating conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22 I.3 Vibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23 I.3.3.2 Location of measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23 I.3.5.3 Operating conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23 I.3.6.2 Declaration of the vibration total value . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23 UL COPYRIGHTED MATERIAL – NOT AUTHORIZED FOR FURTHER REPRODUCTION OR Annex K (normative) Battery tools and battery packs Annex L (normative) Battery tools and battery packs provided with mains connection or non-isolated sources Bibliography UL COPYRIGHTED MATERIAL – NOT AUTHORIZED FOR FURTHER REPRODUCTION OR This document is only permissible for use by claire.hu@intertek.com of Intertek, Electrical/Wireless, Qinzhou, Shanghai, China. 1/5/2017 5:06:55 AM Preface This document is only permissible for use by claire.hu@intertek.com of Intertek, Electrical/Wireless, Qinzhou, Shanghai, China. 1/5/2017 5:06:55 AM This is the harmonized CSA Group and UL Standard For Electric Motor-Operated Hand-Held Tools, Transportable Tools And Lawn And Garden Machinery – Safety – Part 2-14: Particular Requirements for Hand-Held Planers. It is the First edition of CAN/CSA-C22.2 No. 62841-2-14 and the First edition of UL 62841-2-14. This harmonized standard is based on IEC Publication 62841-2-14: First edition Standard For Electric Motor-Operated Hand-Held Tools, Transportable Tools And Lawn And Garden Machinery – Safety – Part 2-14: Particular Requirements for Hand-Held Planers issued June 2015. IEC publication 62841-2-14 is copyrighted by the IEC. Note: At the time of publication, 62841-2-14:2015 is available from IEC in English only. CSA will publish the French version when it becomes available from IEC. This harmonized standard was prepared by CSA Group and Underwriters Laboratories Inc. (UL). The efforts and support of the International Harmonization Committee (IHC) for the adoption of the IEC series of standards for Hand-Held, Motor-Operated, and Transportable Tools and Lawn and Garden Machinery UL are gratefully acknowledged. This standard is considered suitable for use for conformity assessment within the stated scope of the standard. This standard was reviewed by the CSA Subcommittee on Safety of Hand-Held Motor-Operated Electric Tools, under the jurisdiction of the CSA Technical Committee on Consumer and Commercial Products and the CSA Strategic Steering Committee on Requirements for Electrical Safety, and has been formally approved by the CSA Technical Committee. This standard has been approved as a National Standard of Canada by the Standards Council of Canada (SCC). This standard has been approved by the American National Standards Institute (ANSI) as an American National Standard. Application of Standard Where reference is made to a specific number of samples to be tested, the specified number is to be considered a minimum quantity. Note: Although the intended primary application of this standard is stated in its scope, it is important to note that it remains the responsibility of the users of the standard to judge its suitability for their particular purpose. This CAN/CSA-C22.2 No. 62841-2-14, Standard For Electric Motor-Operated Hand-Held Tools, Transportable Tools And Lawn And Garden Machinery – Safety – Part 2-14: Particular Requirements for Hand-Held Planers is to be used in conjunction with the First edition of CAN/CSA-C22.2 No. 62841-1. The requirements for hand-held planers are contained in this Part 2 Standard and CAN/CSA-C22.2 No. 62841-1. Requirements of this Part 2 Standard, where stated, amend the requirements of CAN/CSA-C22.2 No. 62841-1. Where a particular subclause of CAN/CSA-C22.2 No. 62841-1 is not mentioned in CAN/CSA-C22.2 No. 62841-2-14, the CAN/CSA-C22.2 No. 62841-1 subclause applies. UL COPYRIGHTED MATERIAL – NOT AUTHORIZED FOR FURTHER REPRODUCTION OR This UL 62841-2-14 Standard For Electric Motor-Operated Hand-Held Tools, Transportable Tools And Lawn And Garden Machinery – Safety – Part 2-14: Particular Requirements for Hand-Held Planers, is to be used in conjunction with the First edition of UL 62841-1. The requirements for hand-held planers are contained in this Part 2 Standard and UL 62841-1. Requirements of this Part 2 Standard, where stated, amend the requirements of UL 62841-1. Where a particular subclause of UL 62841-1 is not mentioned in UL 62841-2-14, the UL 62841-1 subclause applies. This document is only permissible for use by claire.hu@intertek.com of Intertek, Electrical/Wireless, Qinzhou, Shanghai, China. 1/5/2017 5:06:55 AM Level of harmonization This standard adopts the IEC text with editorial national differences. This standard is published as an equivalent standard for CSA Group and UL. An equivalent standard is a standard that is substantially the same in technical content, except as follows: Technical national differences are allowed for codes and governmental regulations as well as those recognized as being in accordance with NAFTA Article 905, for example, because of fundamental climatic, geographical, technological, or infrastructural factors, scientific justification, or the level of protection that the country considers appropriate. Presentation is word for word except for editorial changes. All national differences from the IEC text are included in the CSA Group and UL versions of the standard. While the technical content is the same in each organization’s version, the format and presentation may differ. Reasons for Differences From IEC National Differences from the IEC are being added in order to address safety and regulatory situations present in the US and Canada. Interpretations The interpretation by the standards development organization of an identical or equivalent standard is based on the literal text to determine compliance with the standard in accordance with the procedural rules of the standards development organization. If more than one interpretation of the literal text has been identified, a revision is to be proposed as soon as possible to each of the standards development organizations to more accurately reflect the intent. IEC Copyright For CSA Group, the text, figures, and tables of International Electrotechnical Commission Publication IEC 62841-2-14 Electric Motor-Operated Hand-Held Tools, Transportable Tools And Lawn And Garden Machinery – Safety – Part 2-14: Particular Requirements for Hand-Held Planers, copyright 2015, are used in this standard with the consent of the International Electrotechnical Commission. The IEC Foreword is not a part of the requirements of this standard but is included for information purposes only. For UL, the text, figures and tables of IEC publication IEC 62841-2-14, Standard For Electric Motor-Operated Hand-Held Tools, Transportable Tools And Lawn And Garden Machinery – Safety – Part 2-14: Particular Requirements for Hand-Held Planers, copyright 2015 are used in this standard with the consent of the IEC and the American National Standards Institute (ANSI). The IEC copyrighted material has been reproduced with permission from ANSI. ANSI should be contacted regarding the reproduction of any portion of the IEC material. The IEC Foreword is not a part of the requirements of this standard but is included for information purposes only. Copies of IEC Publication IEC 62841-2-14 may be purchased from ANSI, 25 West 43rd Street, 4th Floor, New York, New York, 10036, (212) 642- 4900. UL COPYRIGHTED MATERIAL – NOT AUTHORIZED FOR FURTHER REPRODUCTION OR NATIONAL DIFFERENCES This document is only permissible for use by claire.hu@intertek.com of Intertek, Electrical/Wireless, Qinzhou, Shanghai, China. 1/5/2017 5:06:55 AM National Differences from the text of International Electrotechnical Commission (IEC) Publication IEC 62841-2-14, Electric Motor-Operated Hand-Held Tools, Transportable Tools And Lawn And Garden Machinery – Safety – Part 2-14: Particular Requirements for Hand-Held Planers) copyright 2015 are indicated by notations (differences) and are presented in bold text. The national difference type is included in the body. There are five types of National Differences as noted below. The difference type is noted on the first line of the National Difference in the standard. The standard may not include all types of these National Differences. DR – These are National Differences based on the national regulatory requirements. D1 – These are National Differences which are based on basic safety principles and requirements, elimination of which would compromise safety for consumers and users of products. D2 – These are national differences from IEC requirements based on existing safety practices. These requirements reflect national safety practices, where empirical substantiation (for the IEC or national requirement) is not available or the text has not been included in the IEC standard. DC – These are National Differences based on the component standards and will not be deleted until a particular component standard is harmonized with the IEC component standard. DE – These are National Differences based on editorial comments or corrections. Each national difference contains a description of what the national difference entails. Typically one of the following words is used to explain how the text of the national difference is to be applied to the base IEC text: Addition / Add - An addition entails adding a complete new numbered clause, subclause, table, figure, or annex. Addition is not meant to include adding select words to the base IEC text. Modification / Modify - A modification is an altering of the existing base IEC text such as the addition, replacement or deletion of certain words or the replacement of an entire clause, subclause, table, figure, or annex of the base IEC text. Deletion / Delete - A deletion entails complete deletion of an entire numbered clause, subclause, table, figure, or annex without any replacement text. UL COPYRIGHTED MATERIAL – NOT AUTHORIZED FOR FURTHER REPRODUCTION OR INTERNATIONAL ELECTROTECHNICAL COMMISSION This document is only permissible for use by claire.hu@intertek.com of Intertek, Electrical/Wireless, Qinzhou, Shanghai, China. 1/5/2017 5:06:55 AM ELECTRIC MOTOR-OPERATED HAND-HELD TOOLS, TRANSPORTABLE TOOLS AND LAWN AND GARDEN MACHINERY – SAFETY – PART 2-14: PARTICULAR REQUIREMENTS FOR HAND-HELD PLANERS FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and nongovernmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 62841-2-14 has been prepared by IEC technical committee 116: Safety of motor-operated electric tools. The text of this standard is based on the following documents: UL COPYRIGHTED MATERIAL – NOT AUTHORIZED FOR FURTHER REPRODUCTION OR FDIS Report on voting This document is only permissible for use by claire.hu@intertek.com of Intertek, Electrical/Wireless, Qinzhou, Shanghai, China. 1/5/2017 5:06:55 AM 116/222/FDIS 116/236/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. This Part 2-14 is to be used in conjunction with the first edition of IEC 62841-1:2014. This Part 2-14 supplements or modifies the corresponding clauses in IEC 62841-1, so as to convert it into the IEC Standard: Particular requirements for hand-held planers. Where a particular subclause of Part 1 is not mentioned in this Part 2-14, that subclause applies as far as reasonable. Where this standard states ″addition″, ″modification″ or ″replacement″, the relevant text in Part 1 is to be adapted accordingly. The following print types are used: – requirements: in roman type – test specifications: in italic type; NOTES: IN SMALLER ROMAN TYPE The terms defined in Clause 3 are printed in bold typeface. Subclauses, notes and figures which are additional to those in Part 1 are numbered starting from 101. A list of all parts of the IEC 62841 series, under the general title: Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery – Safety, can be found on the IEC website. The committee has decided that the contents of this publication will remain unchanged until the stability date indicated on the IEC web site under ″http://webstore.iec.ch″ in the data related to the specific publication. At this date, the publication will be • reconfirmed, • withdrawn, • replaced by a revised edition, or • amended. A bilingual version of this publication may be issued at a later date. NOTE The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 36 months from the date of publication. UL COPYRIGHTED MATERIAL – NOT AUTHORIZED FOR FURTHER REPRODUCTION OR 101DV DE Modification: Add the following to the IEC Foreword: This document is only permissible for use by claire.hu@intertek.com of Intertek, Electrical/Wireless, Qinzhou, Shanghai, China. 1/5/2017 5:06:55 AM The numbering system in the standard uses a space instead of a comma to indicate thousands and uses a comma instead of a period to indicate a decimal point. For example, 1 000 means 1,000 and 1,01 means 1.01. 102DV DE Modification: Add the following to the IEC Foreword: For this Standard, all references to ″Part 1″ refer to CAN/CSA-C22.2 No. 62841-1 and UL 62841-1. UL COPYRIGHTED MATERIAL – NOT AUTHORIZED FOR FURTHER REPRODUCTION OR ELECTRIC MOTOR-OPERATED HAND-HELD TOOLS, TRANSPORTABLE TOOLS AND LAWN AND GARDEN MACHINERY – SAFETY – PART 2-14: PARTICULAR REQUIREMENTS FOR TRANSPORTABLE HAND-HELD PLANERS 1 Scope This clause of Part 1 is applicable, except as follows: Addition: This part of IEC 62841 applies to planers. 2 Normative references This clause of Part 1 is applicable. 3 Terms and definitions This clause of Part 1 is applicable, except as follows: Additional definitions: 3.101 planer: tool intended for removing surface material, equipped with a rotating cutting head where the axis of rotation of the cutting head is parallel to the plane of the base plate, which is the part supporting the planer on the workpiece Note 1 to entry: The base plate consists of a fixed shoe and an adjustable shoe that determines the depth of cut. 3.102 lift-off device: device which keeps the blade(s) from making contact with a flat surface when the base plate of the planer is attempted to be placed on the flat surface 3.103 cutting head: assembly of blades, cutter block, blade fixing elements, relevant screws and spindle, the whole being ready for working 4 General requirements This clause of Part 1 is applicable. 5 General conditions for the tests This clause of Part 1 is applicable, except as follows: 5.17 Addition: The mass of the tool includes the cutting head including blades and the dust extraction adapter, if any. UL COPYRIGHTED MATERIAL – NOT AUTHORIZED FOR FURTHER REPRODUCTION OR This document is only permissible for use by claire.hu@intertek.com of Intertek, Electrical/Wireless, Qinzhou, Shanghai, China. 1/5/2017 5:06:55 AM 6 Radiation, toxicity and similar hazards This clause of Part 1 is applicable. 7 Classification This clause of Part 1 is applicable. 8 Marking and instructions This clause of Part 1 is applicable, except as follows: 8.1 Addition: – rated no-load speed. 8.3 Addition: – direction of rotation of the working spindle. This shall be indicated by an arrow, raised or sunk, or by other means no less visible and indelible. 8.14.1 Addition: For planers, the additional safety instructions as specified in 8.14.1.101 shall be given. This part may be printed separately from the ″General power tool safety warnings″. 8.14.1.101 Safety instructions for planers a) Wait for the cutter to stop before setting the tool down. An exposed rotating cutter may engage the surface leading to possible loss of control and serious injury. b) Hold the power tool by insulated gripping surfaces, because the cutter may contact its own cord. Cutting a ″live″ wire may make exposed metal parts of the power tool ″live″ and could give the operator an electric shock. c) Use clamps or another practical way to secure and support the workpiece to a stable platform. Holding the workpiece by your hand or against the body leaves it unstable and may lead to loss of control. 8.14.2 b) Addition: 101) instructions on how to adjust the entire range of the depth of cut; 102) instruction on the correct use of the dust collection system. 8.14.2 c) Addition: 101) information about types of cutting heads which can be used, if applicable; 102) instructions for the changing of the blades and their adjustment to the correct position; 103) instruction on how to properly clean/clear the chip ejection opening. UL COPYRIGHTED MATERIAL – NOT AUTHORIZED FOR FURTHER REPRODUCTION OR This document is only permissible for use by claire.hu@intertek.com of Intertek, Electrical/Wireless, Qinzhou, Shanghai, China. 1/5/2017 5:06:55 AM 9 Protection against access to live parts This clause of Part 1 is applicable. 10 Starting This clause of Part 1 is applicable. 11 Input and current This clause of Part 1 is applicable. 12 Heating This clause of Part 1 is applicable. 13 Resistance to heat and fire This clause of Part 1 is applicable. 14 Moisture resistance This clause of Part 1 is applicable. 15 Resistance to rusting This clause of Part 1 is applicable. 16 Overload protection of transformers and associated circuits This clause of Part 1 is applicable. 17 Endurance This clause of Part 1 is applicable, except as follows: 17.101 If a lift-off device is provided to meet the requirements of 18.8 or 21.18.1.1, it shall be sufficiently durable. Compliance is checked by a new tool sample completing the following test. The planer is to be set in horizontal position. The lift-off device is cycled through its intended range of operation for 50 000 cycles. This sequence is repeated at a rate not less than 10 cycles per minute. After completion of the cycling test as specified above, the planer shall then comply with 19.111. 18 Abnormal operation This clause of Part 1 is applicable, except as follows: 18.8 Replacement of Table 4 by the following: UL COPYRIGHTED MATERIAL – NOT AUTHORIZED FOR FURTHER REPRODUCTION OR This document is only permissible for use by claire.hu@intertek.com of Intertek, Electrical/Wireless, Qinzhou, Shanghai, China. 1/5/2017 5:06:55 AM Table 4 – Required performance levels Power switch – prevent unwanted switch-on c Power switch – provide desired switch-off for planers with lift-off device a Power switch – provide desired switch-off for planers without lift-off device b Any electronic control to pass the test of 18.3 a Overspeed prevention to prevent output speed above 130% of rated no-load speed Provide desired direction of rotation a Prevent exceeding thermal limits as in Clause 18 a Prevent self-resetting as required in 23.3 b Lock-off function as required by 21.18.1.2 b 19 Mechanical hazards This clause of Part 1 is applicable, except as follows: 19.1 Addition: For the requirements given in 19.107, 19.108 and 19.109, only the test probe shown in Figure 102 is used. 19.4.101 Planers with a mass according to 5.17 exceeding 3 kg shall have at least two handles. The auxiliary handle, if any, may also be used for the depth-of-cut setting, provided the adjustment of depth of cut is achieved by a rotary action. Compliance is checked by inspection and by measurement. 19.101 The cutting head shall be cylindrically shaped except for the blades, the gullet and the blade clamping means. The maximum gullet width s shall be smax = 0,235 d + 7,2 mm where d is the diameter of the rotating circle of the cutting edges. See Figure 101. Compliance is checked by inspection and by measurement. 19.102 The blades when aligned with the fixed shoe shall not project by more than 1,1 mm radially beyond the cutter block (as per dimension ″a″ in Figure 101). Compliance is checked by measurement. 19.103 At any depth of cut, the distance ″b″ (see Figure 101) between the rotating circle of the cutting edges and the trailing edge on the adjustable shoe shall not exceed 5 mm measured radially. Compliance is checked by inspection and by measurement. UL COPYRIGHTED MATERIAL – NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL This document is only permissible for use by claire.hu@intertek.com of Intertek, Electrical/Wireless, Qinzhou, Shanghai, China. 1/5/2017 5:06:55 AM Type and purpose of SCF Minimum Performance Level (PL) b 19.104 The blades shall be secured in the cutter block in such a way that friction alone is not relied upon to prevent the radial ejection of the blades. This document is only permissible for use by claire.hu@intertek.com of Intertek, Electrical/Wireless, Qinzhou, Shanghai, China. 1/5/2017 5:06:55 AM Compliance is checked by inspection. 19.105 Cutting heads shall be designed and made of such materials that they withstand the forces and loads expected in normal use. Compliance is checked by the following test: An overspeed test shall be made on a sample cutting head, equipped with blades for the largest cutting diameter and the largest cutting edge width, the test speed being 1,5 times the rated no-load speed. If applicable, tension elements such as clamping screws shall be tightened in accordance with the instructions required by 8.14.2 b). After the test, the cutting head shall not be deformed or cracked, no screws shall be loosened and displacements of separable parts shall be less than specified in the test procedure. The test procedure is as follows: 1) Measure the cutting head dimensions. 2) Bring the cutting head to the rated no-load speed, for 1 min. 3) Stop and re-measure the cutting head; measured displacements of the separable parts of the cutting head shall not be greater than 0,15 mm. 4) Bring the cutting head to the test speed, for 1 min. 5) Stop and re-measure the cutting head and compare the results with those obtained from step 3. The compared displacements shall not exceed 0,15 mm. 19.106 Clamping screws or bolts shall not project beyond the cutter block as shown in Figure 101. Compliance is checked by inspection. 19.107 It shall not be possible to inadvertently touch rotating parts from the sides of the planer, except for the cases covered by 19.108. Compliance is checked by the following test: The planer is set to minimum depth of cut and is positioned with the shoes resting on a flat surface that extends beyond the planer by at least 100 mm in all directions. Any lift-off device is disabled. The accessibility is checked by means of the test probe shown in Figure 102 with a force not exceeding 5 N. UL COPYRIGHTED MATERIAL – NOT AUTHORIZED FOR FURTHER REPRODUCTION OR 19.108 Planers with rabbeting facilities shall be provided with a guard that avoids inadvertent contact at the sides with the blades. NOTE Rabbeting is also known as rebating. Compliance is checked by inspection and by the following test: The planer is set to minimum depth of cut and is positioned with the shoes resting on a flat surface that extends beyond the planer by at least 100 mm in all directions. Any lift-off device is disabled. The accessibility is checked by means of the test probe shown in Figure 102 without any force. 19.109 It shall not be possible to touch the blades through the chip ejection opening. Compliance is checked by testing all apertures for chip ejection with the test probe of Figure 102. It shall not be possible to touch the blades in the cutting head at any angle of the probe. 19.110 Planers shall stop within 10 s after switching off. Compliance is checked by inspection and by measurement. 19.111 Lift-off device 19.111.1 If a lift-off device is provided to meet the requirements of 18.8 or 21.18.1.1, it shall meet the requirements of 19.111.2 and 19.111.3, which are checked only after completing the endurance test of 17.101. 19.111.2 If a lift-off device is provided, it shall be designed so that – it is automatically activated, when the planer is lifted up from a horizontal surface; and – the blade(s) do not make contact, when the planer is set at maximum depth of cut in accordance with 8.14.2 b) 101) and placed on a horizontal surface. Compliance is checked by inspection. 19.111.3 A lift-off device shall provide sufficient stability. Compliance is checked by the following test: The planer is set to maximum depth of cut in accordance with 8.14.2 b) 101) and with the supply cord, if any, removed. The planer is then placed on a flat board of medium density fibreboard (MDF) having a density of 650 kg/m3 to 850 kg/m3 that is inclined at an angle of 10°, such that the rear of the planer is nearest to the high side of the board and allowed to rest freely for 10 s to 12 s. During the test, the planer is permitted to slide, however, the liftoff device shall not collapse such that the planer blades come into contact with the board. 20 Mechanical strength This clause of Part 1 is applicable. UL COPYRIGHTED MATERIAL – NOT AUTHORIZED FOR FURTHER REPRODUCTION OR This document is only permissible for use by claire.hu@intertek.com of Intertek, Electrical/Wireless, Qinzhou, Shanghai, China. 1/5/2017 5:06:55 AM 21 Construction This clause of Part 1 is applicable, except as follows: 21.18.1.1 Addition: Planers whose blade(s) make contact with a flat surface when the base plate is placed on the flat surface and without a lift-off device are regarded as tools having a risk associated with continued locked-on operation. NOTE In Europe (EN 62841-2-14), the above text is replaced by the following: For planers, the switch shall not have any locking device to lock it in the ″on″ position. 21.18.1.2 Addition: Planers are regarded as tools having a risk associated with inadvertent starting. 21.35 This subclause of Part 1 is applicable. 22 Internal wiring This clause of Part 1 is applicable. 23 Components This clause of Part 1 is applicable. 24 Supply connection and external flexible cords This clause of Part 1 is applicable. 25 Terminals for external conductors This clause of Part 1 is applicable. 26 Provision for earthing This clause of Part 1 is applicable. 27 Screws and connections This clause of Part 1 is applicable. 28 Creepage distances, clearances and distances through insulation This clause of Part 1 is applicable. This is generated text for figtxt. UL COPYRIGHTED MATERIAL – NOT AUTHORIZED FOR FURTHER REPRODUCTION OR This document is only permissible for use by claire.hu@intertek.com of Intertek, Electrical/Wireless, Qinzhou, Shanghai, China. 1/5/2017 5:06:55 AM This is generated text for figtxt. Figure 101 – Examples of cutting heads with basic dimensions a) Example 1 and explanation of basic dimensions Key 1 fixed shoe 2 adjustable shoe 3 trailing edge a radial projection of the blades beyond the cutter block b distance between the rotating circle of the cutting edges and the trailing edge of the adjustable shoe d diameter of the rotating circle of the cutting edges s gullet width UL COPYRIGHTED MATERIAL – NOT AUTHORIZED FOR FURTHER REPRODUCTION OR This document is only permissible for use by claire.hu@intertek.com of Intertek, Electrical/Wireless, Qinzhou, Shanghai, China. 1/5/2017 5:06:55 AM This is generated text for figtxt. Figure 101 – Examples of cutting heads with basic dimensions b) Example 2 Key 1 fixed shoe 2 adjustable shoe 3 trailing edge a radial projection of the blades beyond the cutter block b distance between the rotating circle of the cutting edges and the trailing edge of the adjustable shoe d diameter of the rotating circle of the cutting edges s gullet width UL COPYRIGHTED MATERIAL – NOT AUTHORIZED FOR FURTHER REPRODUCTION OR This document is only permissible for use by claire.hu@intertek.com of Intertek, Electrical/Wireless, Qinzhou, Shanghai, China. 1/5/2017 5:06:55 AM Figure 102 – Test probe Key 1 handle section 2 test section 3 probe’s flange UL COPYRIGHTED MATERIAL – NOT AUTHORIZED FOR FURTHER REPRODUCTION OR This document is only permissible for use by claire.hu@intertek.com of Intertek, Electrical/Wireless, Qinzhou, Shanghai, China. 1/5/2017 5:06:55 AM Dimensions in millimetres Annexes This document is only permissible for use by claire.hu@intertek.com of Intertek, Electrical/Wireless, Qinzhou, Shanghai, China. 1/5/2017 5:06:55 AM The annexes of Part 1 are applicable except as follows. UL COPYRIGHTED MATERIAL – NOT AUTHORIZED FOR FURTHER REPRODUCTION OR Annex I (informative) Measurement of noise and vibration emissions NOTE In Europe (EN 62841-2-14), Annex I is normative. I.2 Noise test code (grade 2) This clause of Part 1 is applicable except as follows: I.2.4 Installation and mounting conditions of the power tools during noise tests Addition: Planers are held and used as specified in I.2.5. I.2.5 Operating conditions Addition: Planers are tested under load observing the conditions shown in Table I.101. The temperature requirements of 5.6 are not applicable. Table I.101 – Test conditions Orientation Planing along a horizontal surface of a softwood workpiece free of knots and having a residual moisture not exceeding 14 %. To prevent absorption of airborne noise, the resilient material shall either – not extend the contact area between workpiece and test bench; or – be of non airborne-sound absorbing material, such as rubber. If a parallel guide is provided, this may be used. NOTE Examples of softwood are pine and fir. Tool bit Blade as specified for planing softwood. The depth of cut shall be set to maximum capacity. UL COPYRIGHTED MATERIAL – NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL Table I.101 – Test conditions Continued on Next Page This document is only permissible for use by claire.hu@intertek.com of Intertek, Electrical/Wireless, Qinzhou, Shanghai, China. 1/5/2017 5:06:55 AM The workpiece shall have a minimum length of 600 mm, a minimum height of 90 mm and a width B, where B is the maximum planing width of the tool minus (15 ±2) mm. The workpiece shall be supported on resilient material and fixed vertically by screws, clamps, air cylinders or the like to a test bench of Figure I.1, see Figure I.101. For the fixing, the workpiece may have recesses or the like; an example is shown in Figure I.101. The resilient material shall be mounted so that it does not have any significant resonance in the frequency range that can influence the test result. Table I.101 – Test conditions Continued Feed force As necessary to achieve a constant feed rate resulting in 10 s to 15 s planing time for one test cycle (600 mm). Equal forces are applied to the main handle and the auxiliary handle, if applicable, avoiding excessive gripping forces. Test cycle Planing the complete length of 600 mm at maximum depth of cut. I.3 Vibration This clause of Part 1 is applicable except as follows: I.3.3.2 Location of measurement Addition: Figures I.102 shows the positions on the main handle and the auxiliary handle, if applicable. I.3.5.3 Operating conditions Addition: Planers are tested under load according to the conditions shown in Table I.101. I.3.6.2 Declaration of the vibration total value Addition: The vibration total value ah of the handle with the highest emission and the uncertainty K shall be declared. This is generated text for figtxt. UL COPYRIGHTED MATERIAL – NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL This document is only permissible for use by claire.hu@intertek.com of Intertek, Electrical/Wireless, Qinzhou, Shanghai, China. 1/5/2017 5:06:55 AM However, if it is not possible to plane the whole surface length within the given time, because the planer may stall, a longer test cycle time is permitted using a feed force as high as possible without stalling the planer. The measurement takes place over a length of approximately 400 mm that does not include the ends of the workpiece. This is generated text for figtxt. Figure I.101 – Test set-up for planers a) Side view Key 1 test bench of Figure I.1 2 resilient material 3 workpiece 4 fixing means (e.g. clamps) UL COPYRIGHTED MATERIAL – NOT AUTHORIZED FOR FURTHER REPRODUCTION OR This document is only permissible for use by claire.hu@intertek.com of Intertek, Electrical/Wireless, Qinzhou, Shanghai, China. 1/5/2017 5:06:55 AM This is generated text for figtxt. Figure I.101 – Test set-up for planers b) Front view Key 1 test bench of Figure I.1 2 resilient material 3 workpiece 4 fixing means (e.g. clamps) UL COPYRIGHTED MATERIAL – NOT AUTHORIZED FOR FURTHER REPRODUCTION OR This document is only permissible for use by claire.hu@intertek.com of Intertek, Electrical/Wireless, Qinzhou, Shanghai, China. 1/5/2017 5:06:55 AM Figure I.102 – Position of transducers This document is only permissible for use by claire.hu@intertek.com of Intertek, Electrical/Wireless, Qinzhou, Shanghai, China. 1/5/2017 5:06:55 AM UL COPYRIGHTED MATERIAL – NOT AUTHORIZED FOR FURTHER REPRODUCTION OR Annex K (normative) Battery tools and battery packs K.1 Scope Addition: All clauses of this Part 2-14 apply unless otherwise specified in this annex. K.8.14.1.101 Item b) is not applicable. K.12.2.1 This subclause is not applicable. K.20.5 This subclause is not applicable. K.21.18.1.2 Addition: Two separate and dissimilar actions shall be necessary before the motor is switched on (e.g. a power switch which has to be pushed in before it can be moved laterally to close the contacts to start the motor). It shall not be possible to achieve these two actions with a single grasping motion or a straight line motion. Compliance is checked by inspection and by manual test. K.21.30 This subclause is not applicable. NOTE In Europe (EN 62841-2-14), the following additional subclause applies: K.21.18.Z101 Isolation device Planers with an integral battery shall be equipped with an isolation device to prevent the risk of injury from mechanical hazards during user maintenance that – ensures a reliable disconnection of at least one pole of the battery from the relevant load(s); – has a reliable mechanical link between the manual control and the disconnecting element(s); – is equipped with an unambiguous indication of the state of the disconnection device which corresponds to each position of its manual control (actuator); – protects against accidental reconnection. NOTE 1 Examples of methods to achieve this disconnection include removable jumpers, removable batteries or a electromechanical power switch with a direct mechanical link between the actuator and the contact. NOTE 2 The risk of accidental reconnection for a power switch is addressed by the requirement of 21.18.1.2. The other examples in Note 1 achieve this by the necessary actions for reconnection. Compliance is checked by inspection. UL COPYRIGHTED MATERIAL – NOT AUTHORIZED FOR FURTHER REPRODUCTION OR This document is only permissible for use by claire.hu@intertek.com of Intertek, Electrical/Wireless, Qinzhou, Shanghai, China. 1/5/2017 5:06:55 AM Annex L (normative) Battery tools and battery packs provided with mains connection or non-isolated sources L.1 Scope Addition: All clauses of this Part 2-14 apply unless otherwise specified in this annex. L.21.18.1.2 Addition: Two separate and dissimilar actions shall be necessary before the motor is switched on (e.g. a power switch which has to be pushed in before it can be moved laterally to close the contacts to start the motor). It shall not be possible to achieve these two actions with a single grasping motion or a straight line motion. Compliance is checked by inspection and by manual test. NOTE In Europe (EN 62841-2-14), the following additional subclause applies: L.21.18.Z101 Isolation device Planers with an integral battery shall be equipped with an isolation device to prevent the risk of injury from mechanical hazards during user maintenance that – ensures a reliable disconnection of at least one pole of the battery from the relevant load(s); – has a reliable mechanical link between the manual control and the disconnecting element(s); – is equipped with an unambiguous indication of the state of the disconnection device which corresponds to each position of its manual control (actuator); – protects against accidental reconnection. NOTE 1 Examples of methods to achieve this disconnection include removable jumpers, removable batteries or a electromechanical power switch with a direct mechanical link between the actuator and the contact. NOTE 2 The risk of accidental reconnection for a power switch is addressed by the requirement of 21.18.1.2. The other examples in Note 1 achieve this by the necessary actions for reconnection. Compliance is checked by inspection. UL COPYRIGHTED MATERIAL – NOT AUTHORIZED FOR FURTHER REPRODUCTION OR This document is only permissible for use by claire.hu@intertek.com of Intertek, Electrical/Wireless, Qinzhou, Shanghai, China. 1/5/2017 5:06:55 AM Bibliography The bibliography of Part 1 is applicable. UL COPYRIGHTED MATERIAL – NOT AUTHORIZED FOR FURTHER REPRODUCTION OR This document is only permissible for use by claire.hu@intertek.com of Intertek, Electrical/Wireless, Qinzhou, Shanghai, China. 1/5/2017 5:06:55 AM This document is only permissible for use by claire.hu@intertek.com of Intertek, Electrical/Wireless, Qinzhou, Shanghai, China. 1/5/2017 5:06:55 AM No Text on This Page UL COPYRIGHTED MATERIAL – NOT AUTHORIZED FOR FURTHER REPRODUCTION OR This document is only permissible for use by claire.hu@intertek.com of Intertek, Electrical/Wireless, Qinzhou, Shanghai, China. 1/5/2017 5:06:55 AM UL COPYRIGHTED MATERIAL – NOT AUTHORIZED FOR FURTHER REPRODUCTION OR